Advertising
www.apricorn.com
8
How do I use the Aegis Padlock DT the first time?
This item Apricorn Aegis Padlock 4 TB DT 256-bit Encryption USB 3 Hard Drive (ADT-3PL256-4000) Apricorn Aegis Padlock Fortress FIPS 140-2 Level 2 Validated 256-bit Encrypted USB 3.0 Hard Drive with PIN Access, black, 2 TB - A25-3PL256-2000F. User Manuals Apricorn Padlock Easy to use FIPS 140-2 Level 3 validated USB 3.0 flash drive with on-the-fly AES hardware encryption and secure PIN access The Aegis Secure Key automatically locks once you unplug the drive from your computer's Quick Start Guide.
What if I forget the User PIN?
Use your Admin PIN to enter Admin Mode, and then create another User PIN in
Admin Mode.
Admin Mode.
NOTE: If you forget or lose your ADMIN PIN there is no way to access
the drive. Even an Apricorn employee will be unable to help you access
your data. In the event that this happens, the only way to use the drive
is to do a complete reset, which will reset the encryption key making all
data on the drive unrecoverable.
the drive. Even an Apricorn employee will be unable to help you access
your data. In the event that this happens, the only way to use the drive
is to do a complete reset, which will reset the encryption key making all
data on the drive unrecoverable.
Homedics mybaby soundspa lullaby user manual instructions. See the Chapter “Completely Resetting your Aegis Padlock DT” for
instructions.
instructions.
Before the Padlock DT can be used, the Admin PIN MUST be set. The LED will display
Solid
Solid
BLUE
and Solid
GREEN
to indicate the Padlock is waiting for a PIN to be set.
To Set-up the Admin PIN:
1. Press UNLOCK + 9. The LED will change to Solid
BLUE
and Blinking
GREEN
.
2. Enter the new Admin PIN and press UNLOCK key. If accepted the
GREEN
LED will
flash for three short blinks, then return to Solid
BLUE
User manual for kenmore elite dryer bodel 796 61512210. and Blinking
GREEN
.
3. Re-enter the Admin PIN and press the UNLOCK key. If accepted the
GREEN
LED
will be Solid for three seconds.
4. LED will then turn
BLUE
and remain in Admin mode for 30 seconds or if the Cancel
key is pressed, will return the drive to a standby state.
5. The Admin PIN is now set and will allow access to the drive or the Admin features.
6. To UNLOCK
the drive, exit Admin by pressing the Cancelol button. Then enter the
new PIN and press UNLOCK.
*Note: PINs must be a minimum length of 7 maximum 16 digits.
Cannot contain all consecutive numbers (2345678 or 9876543)
Cannot contain all same number (1111111)
Advertising
Popular Brands
Popular manuals
Aegis Padlock Dt Fips
Advertising
www.apricorn.com
16
Completely resetting the Aegis Padlock DT
If you forget all the User PINs or Admin PINs, you can perform a complete reset to
remove all the User PINs, and the Admin PIN.
remove all the User PINs, and the Admin PIN.
Attention: Completely resetting the Aegis Padlock DT will perform a
crypto-erase and reset the encryption key, in effect making all the data on
the drive unrecoverable. You will need to partition and format the Aegis
Padlock DT with disk management applications.
crypto-erase and reset the encryption key, in effect making all the data on
the drive unrecoverable. You will need to partition and format the Aegis
Padlock DT with disk management applications.
To perform a complete reset of the drive, do the following:
1.
Connect the Aegis Padlock DT to an available USB port. Turn on the power
switch on the back of the drive while holding the Cancel button. The LED
switch on the back of the drive while holding the Cancel button. The LED
will flash
RED
,
GREEN
and
BLUE
alternately.
2. Release the Cancel button.
3. Press and hold Cancel + UNLOCK + 2 for ten seconds until the LED turns
Solid
GREEN
for two seconds, followed by Solid
BLUE
and Solid
GREEN
.
You have successfully reset the Aegis Padlock DT.
Initializing and formatting the Aegis Padlock DT
after a complete reset
after a complete reset
A complete reset of the Aegis Padlock DT will erase all information and partition
settings. You will need to initialize and format the Aegis Padlock DT.
settings. You will need to initialize and format the Aegis Padlock DT.
To initialize your Aegis Padlock DT, do the following:
1.
After a complete reset, attach the Aegis Padlock DT to the computer.
2.
Wait five seconds for the computer to recognize the device.
3.
Press UNLOCK + 9. The LED will change to Solid
BLUE
/ Blinking
GREEN
.
4.
Enter the new Admin PIN and press UNLOCK key. If accepted the LED will
flash three short blinks of the
GREEN
LED, then return to Solid
BLUE
and
Blinking
GREEN
.
Advertising
Popular Brands
Popular manuals